Molybdenum plate. Molybdenum plate
Brand: Mo1, Mo3G(MoLa10), TZM, JMo1, Mo 360, MO 361
Executive standard: GB3876-83, ASTM B386-91, GB3877-83
【 Purpose 】 Used in electronics, aviation, aerospace, electric light source, heating body in vacuum furnace, heat insulation screen, molybdenum boat, molybdenum crucible, etc.
Molybdenum plate (piece) Brand:
Mo1, Mo3G(MoLa10), TZM(Molybdenum alloy 364), JMo1, Molybdenum 360, molybdenum 361
Implementation standard of molybdenum plate (piece) :
GB3876-83(Molybdenum and molybdenum alloy plate)
ASTM B386-91(Molybdenum and Molybdenum Alloy Medium Thickness Sheet, Sheet, Strip and Foil)
GB3877-83(Molybdenum foil)
Molybdenum plate (piece) Use:
Used in electronics, aviation, aerospace, electric light source, vacuum furnace heating body, heat shield, molybdenum boat, molybdenum crucible, etc.
The brand, condition and specification of molybdenum sheet are shown in the following table:以上翻译结果来自有道神经网络翻译（YNMT）· 通用领域
brand | Production method | State of supply | Specification (mm) | ||
thickness | width | length | |||
Mo1 Mo3G TZM JMo1 | Powder metallurgy | Hard state (Y) Stress relief state (m) | 0.1～1.0 | 50～600 | 100～2000 |
Hot rolling condition (R) | 1.0～30 | 50～600 | 100～1500 | ||
Mo1 | Vacuum arc melting | Hard state (Y) Stress relief state (m) | 0.1～1.5 | 50～600 | 100～2000 |
Hot rolling condition (R) | 1.5～30 | 50～600 | 100～1500 | ||
The thickness, width, length and allowable deviation of molybdenum sheet are shown in the table below (unit: mm) :
thickness | Allowable thickness deviation | width | Width allowance deviation | length | Allowable length deviation | |
Ⅰlevel | Ⅱlevel | |||||
0.10～0.15 | ±0.01 | ±0.02 | 50～200 | ±2.0 | 100～2000 | ±5.0 |
>0.15～0.30 | ±0.02 | ±0.03 | 50～500 | ±2.0 | 100～2000 | ±5.0 |
>0.30～0.50 | ±0.03 | ±0.04 | 50～600 | ±2.0 | 100～2000 | ±5.0 |
>0.50～0.70 | ±0.04 | ±0.05 | 50～600 | ±3.0 | 100～2000 | ±5.0 |
>0.70～1.0 | ±0.05 | ±0.08 | 50～600 | ±3.0 | 100～2000 | ±5.0 |
>1.0～2.0 | ±0.06 | ±0.10 | 50～400 | ±5.0 | 100～1200 | ±5.0 |
>2.0～3.0 | ±0.08 | ±0.15 | 50～400 | ±5.0 | 100～1200 | ±5.0 |
>3.0～4.0 | ±0.10 | ±0.20 | 50～400 | ±5.0 | 100～1200 | ±5.0 |
>4.0～5.0 | ±0.12 | ±0.30 | 50～400 | ±5.0 | 100～1200 | ±5.0 |
>5.0～30.0 | ±0.20 | ±0.50 | 50～400 | ±5.0 | 100～1200 | ±5.0 |
Location：
